Tuesday, May 17, 2011

Electricity is Shocking

        We use circuits everyday to power light bulbs and other electronic appliances.  A DC circuit means 'direct current'.  It requires the circuit to be a closed path with a generator, usually a battery, and a load or something like a light bulb or engine. In circuits, wires are often used as conductors, something that the current can flow through easily.   In the examples below, the orange line represents the wires and the light bulb represents light bulbs or all other things that are considered resistors.
        In this posting, there are three types of circuits; series, parallel, and complex, using series and parallel.


 A series circuit means that the total current is equal to the current for each resistor.  The total voltage drop is the sum of the voltage drops for each resistor, but the voltage for a specific resistor may vary.  Voltage is the potential difference between two points.  The voltage drop depends on the amount of resistance that the resistor produces.  The resistors are the 'two points' mentioned earlier.  The importance of the resistors is to limit the voltage in the circuit, to make sure it doesn't burn.  The equation used to find the current, voltage, and resistance is I=V/R.  In a series circuit, if one light bulb is removed, then the whole ciruit stops working.  This circuit provids only one path for the electrons to go through and if one resistor is removed, then the path is disrupted.

A parallel circuit occurs when the path of the current is split.  It provides a diffent path for the electrons to take in case, as an example, on bulb is removed...
... then the other path is open and the electrons go through that path.  This means that the total current in a parallel circuit is equal to the sum of the currents in the resistors.  But in a parallel, unlike the series, the voltage remains the same for each resistor; the total voltage is equal to the voltage of resistor 1 and equal to the voltage in resistor two.  The voltage is the same as it is at the source.  It is if it's a single wire with voltage running through it.  Since voltage is the potential difference between two resistors, for all intents, there is no second resistor.  The risistance in a parallel circuit is equivilent to the average of the two resistors.  If you add more resistors, then the overall resistance is less and the current is greater, but with only two resistors, you get a smaller current.  The equivalant resitance is equal to the amount needed for one resistor to 'do the job'.

A complex circuit means a blend of series and parallel.  In plane words, this image shows two bulbs in parallel, connected to another bulb in series.  You may notice that in this image the bulb in series is brighter than the two bulbs in parallel.  That is because the current in the total parallel is equal to the current for the bulb in series. Once the current is in parallel, it changes depending on the resistance, like any other parallel circuit.  To find the current and voltage for the resistors,  you do the equations for for parallel first, and then imputing the results into the equations for series.
If the bulb on the right is removed, then the whole circuit goes out because it is series.  If the bulb on the top is removed, then the two remaining bulbs become a series becuase the once-parallel circuit provided an alternate path. 
In the picture below, the voltage will be explained.

The voltage in this complex circuit occurs when the total voltage in the series section equal to the voltage in the other path.  The total voltage is equal to the voltage at the source.  The resistance in the series section is double to the resistance on the other path, asuming the resistance for the light bulbs are the same. 

Tuesday, May 10, 2011

If It's Amusement...

        Nordic and Co. was thrilled to be commissioned to build a amusement ride for the new upcoming iPhone App theme park.   We carefully chose Robot Unicorn Attack as our first ride's theme due to the awesomeness of the game and the superiorness that these horses would have, sitting proudly on their carousel, being able to guard the park from any point of view.  Then, as our second ride, we chose cut the rope, a game only for the skilled.  In this game, the player has to carefully guide the candy into the monster's mouth, but in the ride, you want anything but to be swallowed up by it.  Cut the Rope is a pendulum ride where the player is the candy!  Our rides display a multitude of physics, from centripetal force to simple harmonic motion; we strive to do the very best for our customers.  Come to the park when it opens to experience for yourself the conservation of energy and velocity and feel the iPhone power all around you!
Located in room 2165, down the great hall.

For interest in our testing and the specifications of our ride, go to Nordic and Co. Testing Site

prezi presentation coming soon!